EVO-tech 3D Printer

Open System

With our EVO-lizer 3D printers, we offer you the best of both worlds. On the one hand we have an open system, which gives full access to all parameters and allows you to use your own materials. On the other hand, we offer you a variety of our own materials including tested parameters.

Your advantages:

• Good predefined parameter sets

• Independence from the manufacturer

• Lower material costs

• Significantly lower "Total Cost of Ownership"

• Open Slicer

  More about open vs. closed systems

WIDE VARIETY OF MATERIALS

Whether ESD, soft, hard, UV or heat-resistant - with our 16 materials we always have the right filament solution for you. If this is not the case, you can use filaments from third-party suppliers at any time thanks to our open systems.

Your advantages:

• Predefined parameter sets

• Proven filaments

• 1 to 10KG filamentspools

  To the material overview

FULLY AUTOMATIC XYZ CALIBRATION

With an integrated tool length sensor, we can not only measure the nozzle height, but also the X and Y deviations of the nozzles from one another.

Your advantages:

• Fully automatic calibration

• High process reliability

• High reproducibility

• No more test prints required after changing nozzles

• Better dual printing results

Anti-OOZING STATION FOR DRIP-FREE DUAL PRINTING

The Oozingstation prevents material from leaking from one nozzle while another nozzle is printing. This prevents so-called oozing (stringing and dripping on the components).

Your advantages:

• Very good surface quality with dual printing

• High reproducibility

• No material decomposition in the nozzle

• Significantly less cleaning effort

• Shorter printing times

HEATED AND DRIED FILAMENT CHAMBER

Many filaments absorb humidity from the environment, which can lead to significantly poorer printing results, up to and including printing failures. With our integrated drying chamber and its sensors, you always keep an eye on the moisture and thus increase the quality of your components!

Your advantages:

• Better component quality

• High reproducibility

• Less waste with up to 10 kg filament

PRINT BED MEASUREMENT WITH UP TO 121 POINTS

The integrated, inductive sensor automatically measures the evenness of the bed before printing starts. Large deviations are corrected before printing by moving the Z-axes on one side, small deviations are automatically compensated during printing.

Your advantages:

• No manual measurement necessary

• High reproducibility

• Better component adhesion

UP TO 4 NOZZLE HEADS

Increase your productivity with up to 4 nozzle heads that can be used at the same time, as well as the associated output and material combination options.

Your advantages:

• Parallel printing of 4 identical components -> Reduction of the printing time by a quarter

• Combination of different nozzle diameters -> Fine surface quality for outer wall and fast ejection for filling

• Less set-up times when using different materials on a regular basis

• Combination of up to 4 materials in one print job

M TO XXL PRINT AREA

Its components are not erected on sand, but on a neatly plane-milled aluminum plate, which in turn is mounted on a machined steel frame.

Your advantages:

• Components larger than a Euro pallet are becoming a reality

• Choice between magnet and/or vacuum clamping system

• Heated build platform minimizes warping

• Not tied to any manufacturer's proprietary surface material

• Clever linear expansion concept to minimize deformation when heated

BALL SCREWS, LINEAR GUIDES AND REINFORCED BELTS

Reproducibility and stability begins not only with the design, but also with the correct selection of the axle components. In addition to size and dynamics, 3D printing also includes temperature resistance and linear expansion. With THK we have an industrial partner who can guarantee this.

Your advantages:

• Positioning in hundredths

• Low-maintenance and wear-resistant

• Hardly any backlash effect

• Industry standard guarantees availability of spare parts for decades

• Closed loop drive system

HARDWARE AND SOFTWARE INDUSTRY 4.0

Your advantages:

• Upgrade security and easy expandability through modular CAN bus system

• Communication with G code standard

• Automatic updates via internet or USB stick

• More than 35 sensors ensure a reproducible result

• API for reading real-time data

• UL version available on request

UP TO 7,200 WATTS MAKE THE INTERIOR HEATING GLOW

When processing plastics in general and in the 3D printing welding process in particular, the process temperatures and controllable cooling are crucial for an excellent result.

In the EL-1040, 6 interior heaters, each with 1,200 watts, ensure that the installation space is heated comparatively very quickly and homogeneously.

Your advantages:

• Reproducible results

• Significantly less shrinkage and warping

• Higher component strength

SIMPLE SERVICE

Your advantages:

• Service points accessible without tools

• Printhead change within minutes

• Nozzle change in seconds